slotcars, slot car, new slotcar products, Pro Slot, Camen, Slick 7, PK, GT-1

M736C 3.850 long "Beuf Express" .080 aluminum chassis kit with aluminum motor brace, aluminum pillow blocks and EDM aluminum body brace. $199.00 ea. M736D 3.850 long "Beuf Express" .080 aluminum chassis kit with steel motor brace, aluminum pillow blocks and EDM aluminum body brace. $189.00 ea. M530V Narrow HB-OMB 3.995 long lightweight steel chassis without pans. Kit. $56.39 ea. M530U Narrow HB-OMB 3.995 long lightweight steel chassis without pans. Assembled. $61.39 ea. M742 Bare ultralight endbell for 615 ID G27/C12 cans. No hardware holes. Fits M632 ball bearings. $24.48 ea. M277R10-350 Push-pull 10 mag kit for .450 tall x .350 long qualifying magnets for .480 arms in M471K or M471A cans. $103.50 set M738 Wiper button for all Koford controllers. 6 per card. $.98 ea. M743 EDM drilled, 2mm .040 hole qualifying/race axle. premium plated axles for Eurosport made using ultrahigh strength steel and plated and ground. $16.98 ea. M740 .014 Diaplane. $.75 ea.(6 per card) M741 Air kit for longer cars with .004 sidedams and ,005 spoiler. $2.98 ea.(6 per card)M196-E24-300 1/24 Eurosport motor with small OD can, .300 stack .480 84 arm, 24 mag 450 tall set up and 1.5mm arm shaft. $491.18 ea. M547C Double ball bearing C can set up with M727 can, .450 long ceramic magnets for .518 G12 arms. $68.02 ea. M737-760SW 760 x 3/32 tires with full width Soft Wonder rubber on rim width .615 diameter magnesium hubs. $19.50 pr. M166-5 RTR .005 Aerotek wing body with 5 x 5 air kit. Suitable for G27, C12, Hawk 12, OMB, Group F, cars with for 4.000 to 4.250 guide lead. $36.64 ea. M736A 3.900 long "Beuf Express" .080 aluminum chassis kit with aluminum motor brace, aluminum pillow blocks and EDM aluminum body brace. $199.00 ea. M736B 3.900 long "Beuf Express" .080 aluminum chassis kit with steel motor brace, aluminum pillow blocks and EDM aluminum body brace. $189.00 ea. M530R 4.070 long lightweight HB/OMB chassis. Kit.$56.39 ea. M530Q 4.070 long lightweight HB/OMB chassis. Assembled. $61.39 ea. M530T 3.995 long lightweight HB/OMB chassis. Kit.$56.39 ea. M530S 3.995 long lightweight HB/OMB chassis. Assembled.$61.39 ea. M735 .465 tall Lightweight OD ground G7 Light CNC can with .015 wall and .620 magnet ID. Use with M287-TA or M287-O endbell. $59.00 ea. M732K Ultralight endbell kit for 615 ID cans. Four degree timing advance. Fits M632 ball bearings. $41.75 ea. M732A Assembled ultralight endbells for 615 ID cans. Four degree timing advance. Fits M632 ball bearings. $49.96 ea. M720B NarrowTek C12 3.850 long "Beuf Express" ultralight aluminum chassis kit with aluminum pillow blocks and motor brace. Center weight only 4.10 grams. $154.00 ea. M733 .060 long machined aluminum spacer for 3/32 axles. 6 per bag. $1.98 pk.(6 per cd.) M734 .160 long machined aluminum spacer for 3/32 axles. 6 per bag. $2.29 pk.(6 per cd.) M731A .615 ID Lightweight but strong OD ground 27L CNC can with .012 wall. .418 tall for M277S2-440 magnets. For 485 or 490 arms. $51.54 ea. M277S2-440 For M731A 615 ID 27L cans, .059 thick with stronger material. Suitable for .485 to .490 arms. $74.98 pr. M731B .615 ID Lightweight OD ground C12 CNC can with .012 wall. .480 tall for M277S6-300 magnets. For 485 or 490 arms. $51.54 ea. M277S6-300 480 tall C12 .059 thick 6 mag kit to fit M731B .615 ID can. $86.95 set M732B Bare lightweight aluminum endbell for 615 ID cans. Four degree advanced timing lightweight endbell. Fits M632 ball bearings. $24.98 ea. M709D Beuf Express NarrowTek .050 steel chassis kit with center weight of only 7.41 grams. 3.850 long and .125" narrower then standard. $111.00 ea. M214N-5 NarrowTek (G27L, C12) 1/8” narrower width clear body with dimpled design and additional ribbing for stiffness. Fits NarrowTek 27L chassis. $6.98 ea. M697N 1/8" shorter EDM drilled and wire cut flatted .060 hole hollow race axle for NarrowTek chassis. $27.98 ea. M730 Tri flat light weight G7 race axle. $22.29 ea. M472-680S-WXX .680 diameter, drilled only, magnesium hub tires. Low cost tires for "spec" tire racing with WXX rubber. $16.00 pr. M287O-4 Four degree advanced timing G7-TMO endbell for non capped comms. Fits M629 ball bearings. $24.98 ea. M467-27-B-38 Wound on the famous Tri Star G27 blank this is an .850 long .500 dia. 38° arm featuring the Koford short SAW comm, 800° epoxy, and plated shaft. $79.14 ea. M275EH .235 stack, .664 long, 459 blank ultrashort custom Euro arm with angled comm tabs for F1. Specify diameter, wind and timing. Typical specs are .455-.460 diameter, 44 to 50 of 29 or 30 wire, 28 degree timing. Specify 2.0, 1.5, or 1.25 mm shaft. $103.94 ea. M728 OD ground 1/24ES can with .012 wall. .578 ID x .450 tall for .300 stack arms and mags. $52.35 ea. M729 OD ground 1/32ES can with .012 wall. .578 ID x .430 tall for .240 stack arms and .250 long mags. $52.35 ea. M277E32-250 24 mag (push-pull) kit for M702 or M729 E32 can to fit .480 arms. .430 tall x .046 thick. $158.00 set M166-4 RTR wing body as used on our RTR cars. Suitable for G12, G20, Hawk 12, OMB, Group F, cars with for 4.100 to 4.250 guide lead. $21.99 ea. M397L Aluminum pillow block with body support. For aluminum chassis with steel motor braces. $19.98 pr. M727 H12 and Scale can. Stronger harder steel then M528. Lower gauss then M528 is ideal for H12 and Scale motors. Fits .450 long magnets. Precision formed. $12.59 ea. M277C6-300 480 tall C12 (push-pull) .064 thick 6 mag kit to fit M521 can. $86.95 set M397K Aluminum pillow block. For steel motor braces. $17.90 pr. M709C Ultralight Beuf Express 27L chassis with a center weight of only 8.54 grams. 3.850 long. Comes with body support pillow blocks. $93.70 ea. M277OOL-380 Small outer segments for making .450 tall x .380 long x .072 thick G7 multi mag motors . For .485 and .480 arms. $36.27 (set of 4) M471I .480 tall Lightweight OD ground G7 Light CNC can with .015 wall and .630 magnet ID. $54.37 ea. M471K .450 tall lightweight OD ground G7 Light CNC can with .015 wall and .630 magnet ID. $54.37 ea. M726 .480 tall lightweight OD ground C12 can with .012 wall and .630 magnet ID. $50.95 ea. M725 Aluminum wide motor box brace for chassis with aluminum pillow blocks. $15.95 ea. M397J Aluminum pillow block with body support. For aluminum motor braces. $19.98 pr. M277EV-300 .027 x .300 x .046 center segments. Use to make .450 tall Eurosport 24 mags (1pr. M277EP300, 1pr. M277EO300, 10pr M277EV-300) for M715 small diameter can to fit .480 arms. $14.85 pr. M724S Soft magnet cleaning putty. $3.99 ea. M720A 3.850 long "Beuf Express" ultralight C12 aluminum chassis kit with aluminum pillow blocks and motor brace. $154.00 ea. M721 Hawk 19 motor with Sintered Neo mags and 48° arm. Sintered Neo magnets increase gauss by 10% for more power. $70.95 ea. M645-48 Group 19 (G20 on a .350 long blank) 48° replacement arm for M721 drag motor. Better then drill blank shaft, 800° epoxy. $46.40 ea. M711 Short aluminum pillow block with body support. For aluminum motor braces. $19.98 pr. M722-10 Black Diamond coated hardened 10 tooth 5 degree angled 72 pitch pinion with boss. $7.75 ea. M722-11 Black Diamond coated hardened 10 tooth 5 degree angled 72 pitch pinion with boss. $7.75 ea. M723-11 Black Diamond coated hardened 10 tooth 3 degree angled 72 pitch pinion with boss. $7.75 ea. M277TSR27L .061 thick with stronger material. G27L radial (R) magnets. Use with M471J OD ground cans. This combination saves .5 grams with no loss of magnet strength compared to using a regular can and regular radial magnets.Suitable for .495 to .500 arms. $74.98 pr. M599-9 9 tooth pinion with boss. $3.95 ea. (6 per card) M719 Koford Yellow stickers. Pack of 6. $3.00 pk. M709B 3.850 Beuf Express QuadRail wide motor box G27 light .050 steel chassis kit. $111.00 ea. M471J Lightweight OD ground G27 Light CNC can with .012 wall. .418 tall for M277TR27L magnets. $51.54 ea. M287Q-4 Four degree advanced timing lightweight G27L endbell. Lighter then the competition. Fits M632 ball bearings. $21.98 ea. M287-HC-4 Assembled 4° advanced timing lightweight G27L endbell. Lighter then the competition. Fits M632 ball bearings. $49.50 ea. M472B-SW Drilled (24 holes), waffled and milled hubs. .760 x 3/32 with Soft Wonder rubber. $16.50 pr. M287-AB Bare aluminum endbell to fit the Hawk set up. Fits Koford hardware. Especially designed for Pro F wing car class. $26.98 ea. M287-AK Kit aluminum endbell to fit the Hawk set up. Includes hardware and BB. Especially designed for Pro F wing car class. $43.75 ea. M287-AA Assembled aluminum endbell to fit the Hawk set up. Includes hardware and BB. Especially designed for Pro F wing car class. $50.75 ea. M645-12-40 G12 arm to fit JK Hawk 6 neo magnet set up. Better then drill blank shaft, 800° epoxy. 40° timing. recommended for neo magnet set ups only. $44.36 ea. M717 Precut short braid with precision prebent clip. Short braid is faster then long braid and this braid is already precut to the right length! 12pr. box. $.96 pr. M718 Precut short braid with precision prebent clip. 100pr. $.90 prM531Z wide motor box 3.925 long "Beuf Express" aluminum chassis kit with steel motor brace and aluminum pillow blocks for G7/TMO/OMO/C12. $144.90 ea. M531Y wide motor box 3.925 long "Beuf Express" aluminum chassis kit with aluminum motor brace and aluminum pillow blocks for TMO/OMO/C12 $154.90 ea. M214L-5 Newpeugeot (G7, TMO, G27L) Based on the famed Peugeot design but with additional ribbing to prevent collapse with .005 material. $6.98 ea. M214M-5 Aerotek (G27L, C12) Dimpled design with additional ribbing for stiffness. $6.98 ea. M562-4 Four ohm wire resistor controller with variabrake. $101.93 ea. M467-12-CU Custom C12 arm, .760 long. Specify diameter and timing. $45.90 ea. M277PPS-380 Ultra small outer segments for making .480 tall x .380 long x .072 thick G7 30-42 mag motors . For .485 and .480 arms. $34.20 (set of 4) M715 .620 OD x .450 tall CNC Eurosport can for .300 stack arms. Plated for maximum solder and epoxy bond strength and no rusting. Use with M619M-E arms. $42.35 ea. M712 JK Hawk motor with with bonded Neo magnets and Koford 12 arm, Super Big Foot 2 brushes and silver conductive springs. $61.73 ea. M713 Hawk 12 car with Koford EDM spring steel chassis and Hawk 12 motor. Features hardened solder on pinion, flatted axle, mag rim tires, etc. $194.93 ea. M714 G12 endbell kit with ball bearing , Gold plated horizontal hardware and aluminum spring cups for shunted motors. $23.35 ea. M277OSR-380 Radius tip single piece magnets .480 tall x .380 long x .064 thick for G7 motors where single piece magnets are required. Produces .502 air gap with a light grind when installed in M471B can. For use with .490 arms. $74.98 pr. M277OSS-380 Sharp tip single piece magnets .480 tall x .380 long x .064 thick for G7 motors where single piece magnets are required. Produces .502 air gap with a light grind when installed in m471B can. For use with .490 arms. $74.98 pr. M620-945 K blank, 490 94.5 18° SAW com open arm, fits setups for .840 long arms. $87.55 ea. M541-42 Red Dot ultraprecision 42 tooth gears with magnesium hub. High accuracy. Our superstrength plastic material provides greater crash resistance and reduced wear compared to any competing product. $10.95 ea. M663-42 Drilled Red Dot 42 tooth gears. $11.98 ea. M531X 3.850 long "Beuf Express" aluminum chassis kit with steel brace and aluminum pillow blocks for G7.TMO/OMO/C12. $144.00 ea. M645-12-34 Hawk 12 arm with 34° timing $43.36 ea. M673-5 5 ohm external wire resistor controller with gold plated switch block and high impact handle. $66.99 ea. M709A 3.850 Beuf Express G27 light .050 steel chassis kit. TQ Hill Billy Nat's. $92.50 ea. M710 Steel G27L motor brace for M709A chassis. $9.99 ea. M531W 3.850 aluminum chassis kit with aluminum back end for TMO/G7/C12 $154.00 ea. M472-650S-WH .650 diameter, drilled only, magnesium hub tires. Low cost tires for "spec" tire racing. $16.00 pr. M287-LA Long tower aluminum Euro endbell to fit M652 small OD Euro can with no face holes. Side holes are not tapped. For making advanced timing endbells for arms with caps. $24.98 ea. M706 Steel wide motor brace for chassis with aluminum pillow blocks. $10.95 ea. M707 Steel G27L pillow block with body support. $5.98 ea. M530O 4.120 long Box chassis without pans. Assembled. $55.90 ea. M530P 4.120 long Box chassis without pans. Kit. Winner Hill Billy Nat's. $50.96 ea. M527I Aluminum endbell double bb motor for hillbilly box. $154.21 ea. .650 diameter, drilled only, magnesium hub tires. Low cost tires for "spec" tire racing. M472-650S-WX $16.00 pr. M472-650S-WX+ $16.00 pr. M472-650S-WXX $16.00 pr. M472-650S-WXXX $16.00 pr. M468-H12 Handwound 12 arm to fit Box set ups for “Hillbilly Box” racing. 518 diameter. Specify timing. H12 tag. $55.00 ea. M531V 4.110 long, Beuf Express wide motor box OMO chassis kit with aluminum motor brace and pillow blocks. $154.90 ea. M283-E24-300L 1/24 Euro set up with long tower endbell for capped comms and small OD M652 CNC can with .430 tall 24 mags, vertical hoods to fit .757 long (before capping) x .300 x .480 dia. arms. $343.98 ea. M283-E24-300S 1/24 Euro set up with small OD M652 CNC can with .430 tall 24 mags, vertical hoods to fit .757 long x .300 x .480 dia. arms. $342.98 ea. M277EU-300 .025 tall center segments to make .430 tall Eurosport 24 mags (1pr. M277EP300, 1pr. M277EO300, 8pr M277EU-300) for M652 small diameter can to fit .480 arms. .046 thick. $14.85 pr. M277E24-300 24 mag kit for M652 small diameter can to fit .480 arms. .046 thick. $180.00 set M610Y 4.119 long, wide motor box Beuf Express G27 light .050 steel chassis kit. $88.67 ea. M610Z 4.550 long Beuf Express G27 light .050 steel chassis kit for flatter tracks. $88.67 ea. M705B Bare aluminum Gp12 endbell $26.98 ea. M705A Assembled aluminum Gp 12 endbell. $52.50 ea. M705K Aluminum Gp 12 endbell kit. $43.75 ea. M527H Aluminum endbell G12 motor for scale racing with double ball bearings and shunts. High time arm. Motor is blueprinted and assembled by Koford craftsmen with premium brushes and fully broken in. $140.75 ea. M531U M531U 4.110 long, Beuf Express wide motor box G7 chassis kit. 2016 World's winner. $134.90 ea. M287-QA Lightweight group endbell. Use for making advanced timing endbells. No face holes, side holes untapped.  Fits M632 ball bearings. $16.98 ea. M704 .010 thick Plastic axle spacer for wide motor box cars with 3/32 axles. A snug fit on the axle so that it doesn't fall off. Easy open box of 24. $.35 ea. M530K 4.355 long Box chassis without pans. Assembled. $55.90 ea. M530L 4.355 long Box chassis without pans. Kit. TQ Hill Billy Nat's. $50.96 ea. M530M 4.405 long Box chassis without pans. Assembled. $55.90 ea. M530N 4.405 long Box chassis without pans. Kit. $50.96 ea. M703 Guide tape. High temperature, low friction tape eliminates braid melting to guide. Apply under braid and on side of blade. Protects guide against wear. Just replace tape after each race instead of changing guide. Alternative to putting a screw in the guide when running on new tracks. $34.36 ea. M671-27 Narrowed and lightened precision low wobble 27 tooth x 3/32 crown gears. Precision bored axles hole and lightweight magnesium hub. $7.47 ea. (6 per cd.) M702 Short .620 OD x .430 tall CNC Eurosport can for .240 stack arms. Plated for maximum solder and epoxy bond strength and no rusting. $42.35 ea. M196-E10-250 1/32 Eurosport motor with short small OD can, .240 stack .480 22T-25 arm, 10 mag 435 tall set up and 1.5 mm arm shaft. $373.23 ea. M196-E10-250B 1/32 F1 motor with short small OD can, .240 stack .480 45T-29 arm, 10 mag 435 tall set up and 1.5 mm arm shaft. $373.23 ea. M610W 3.950 World's rules Beuf Express G27L chassis kit $90.50 ea. M610X 4.000 World's rules Beuf Express G27L chassis kit $90.50 ea. M527G 40° .518 arm Ultra G12 blueprinted motor with double ball bearings and shunts. Lightweight can and .450 long magnets. Motor is blueprinted and assembled by Koford craftsmen with premium brushes and fully broken in. $124.66 ea. M472-615 .615 diameter, drilled only, magnesium hub tires. Low cost tires for "spec" tire racing. Available in WH, WX, WX+, WXX, rubber. $13.00 pr. M619M-E .300 stack K blank .480 diameter Eurosport, long comm .757 long arms to fit .480 tall Koford set ups. For 1/24 Euro. The K blank produces maximum horsepower. Specify wind and timing. 84, 84.5, with 20-23° timing suggested. $98.00 ea. M255M-E H blank Eurosport, .300 long stack .480 diameter, long comm .757 long arms to fit .480 tall Koford set ups. For 1/32 or 1/24 Euro. The H blank is lighter and easiest to drive. Specify wind and timing. 22t-25, 25t-25, 26t-26 and 20° to 28° timing suggested. $98.00 ea. M619F-E .240 stack .480 diameter K blank, long comm Eurosport to fit .480 tall Koford set ups. For 1/32 Euro. The K blank produces maximum horsepower. .735 arm length. Specify wind and timing. 22t-25 or 25t-25 and 20° to 28° timing suggested. $98.00 ea. M255F-E .240 stack .480 diameter H blank, long comm Eurosport to fit .480 tall Koford set ups. For 1/32 Euro. The H blank is lighter and easiest to drive. .735 arm length. Specify wind and timing. 22t-25 or 25t-25 and 20° to 28° timing suggested. $98.00 ea. M701 480 tall x 470 long x .167 thick high gauss radially oriented G15 magnets. Radial orientation produces a radial field like a 10 mag motor but the magnets are one piece for maximum durability and ease of installation. $35.00 pr. M610U 4.120 hi bite assembled Beuf Express G27 light .050 steel chassis. $141.27 ea. M610V Kit version of above. $88.67 ea. M700-14 Wing electronic pwm MOSFET controller with voltmeter, 14 feet of electronic choke, sensitivity, choke bypass, Pro variabrake with full off and "mush" button. Cool operating, smooth, light weight and compact with long flexible cord from power module to handle, ideal for traveling. Bracket to hang power module on side of track wall. Infinitely adjustable choke with 1/2 foot steps, get exactly the choke level you want. Linear response eliminates the 1-2 volt jump between the last band and full power with conventional controllers. This results in better control near full power. Response is linear at any sensitivity setting, none of the "controller does nothing until the trigger is almost fully pulled" that many standard transistor controllers have. Full on resistance less then with relay. 25 band switch block. New high impact handle. $589.00 ea. M700-45 Eurosport electronic pwm MOSFET controller with voltmeter, 45 feet of electronic choke, sensitivity, choke bypass, Pro variabrake with full off and "mush" button. Also works for wing cars. Cool operating, smooth, light weight and compact with long flexible cord from power module to handle, ideal for traveling. Bracket to hang power module on side of track wall. Infinitely adjustable choke with 1 foot steps, get exactly the choke level you want. Linear response eliminates the 1-2 volt jump between the last band and full power with conventional controllers. This results in better control near full power. Response is linear at any sensitivity setting, none of the "controller does nothing until the trigger is almost fully pulled" that many standard transistor controllers have. Full on resistance less then with relay. 25 band switch block. New high impact handle. $589.00 ea. M541-44S Red Dot ultraprecision 44 tooth gears with magnesium hub. High accuracy. Our superstrength plastic material provides greater crash resistance and reduced wear compared to any competing product. $10.95 ea. M663-44 Drilled Red Dot 44 tooth gears. $11.98 ea. M620 K blank 490 84, 23° SAW com open arm, fits setups for .850 long arms. $85.00 ea.M467-27B-40 Wound on the famous Tri Star G27 blank this is an .850 long .500 dia. 40° arm featuring the Koford short SAW comm, 800° epoxy, and plated shaft. $85.00 ea. M531Q 4.110 long, Beuf Express OMO chassis. Lightweight chassis for OMO racing on superfast highly banked tracks. $192.21 ea. M531R Kit version of the above. $134.90 ea.